A single component polyurethane foam with an increased yield, curing under the influence of moisture. Contains the components improving work at negative temperatures. With an adapter under the gun.
Назначение:
изоляция и герметизация стыков, заполнение швов и пустот внутри и снаружи помещений. Рекомендуется для установки оконных и дверных блоков, подоконников, тепло- и шумоизоляции ванн и душевых кабин, герметизации крыш, чердаков трубопроводов и др.
Properties:
good adhesion to most surfaces: brick, concrete, stone, plaster, steel, wood, aluminum, polystyrene foam and plastics. Hardened foam is resistant to moisture, mold, fungi. Does not apply to polyethylene, polypropylene, bitumen, silicone, Teflon, materials that emit oils and solvents.
Technical data
Colour | light yellow |
Composition | 4,4′-diisocyanate diphenylmethane, propellant |
Density | 0.020 – 0.025 g / cm3 (20-25 kg / m3) |
Working temperature | -10 ° С / + 30 ° С (optimally + 20 ° С) |
Cylinder temperature | + 15 ° С / + 30 ° С |
Heat resistance | -60 ° С / + 90 ° С |
Film formation time | 8-12 minutes (20 ° C / RH 90%) |
Time to preprocessing * |
30-40 minutes (at 23 ° C) 60-120 minutes (at 0 ° C) up to 180 minutes (at -10 ° C) |
Solidification time | 24 hours |
Thermal conductivity | 0.036 W / mK |
Water absorption | 1.5% (after 24 hours) |
Resilience | 0.05 MPa (when squeezing) 0.14 MPa (when stretching) |
Solvent | acetone (before hardening) |
Combustibility | B3 (DIN 4102) |
Product yield * | about 55-60 liters at 23 ° C about 45-50 liters at 0 ° C about 30-35 liters at -10 ° C |
Storage temperature | + 5 ° С / + 30 ° С (short -5 ° С) |
Shelf life | 18 months |
* depending on temperature and air humidity |
Application:
clean, degrease and moisten the surface. At negative temperatures do not moisten. Heat the balloon (cool) with water up to + 15 ° С / + 30 ° С. Shake well 25-30 times. To remove a protective cap, to wind a cylinder on the gun. The working position of the cylinder – “bottom up”. Fill the seam by 70%, afterwards the foam will expand to the required volume. After 30-40 minutes, trim the excess. Complete curing after 24 hours. Frozen foam must be protected from exposure to UV – radiation: plaster, paint, etc. Not hardened foam is removed with a special cleaner, hardened – by mechanical means. At a break in work more than 15 minutes the tip of the gun should be washed with a cleaner. When removing the bottle from the gun, rinse it thoroughly with a cleaner before removing any foam residue. Store the container upright.
Attention!
S2 Keep out of the reach of children. S16 Do not store near sources of ignition – no smoking. The cylinder is under pressure. Protect from direct sunlight. Do not pierce, do not burn after use. Do not heat above + 50 ° C. Do not spray in front of open flame or hot objects. R20 Damage the respiratory tract. R36 / 37/38 Irritating to eyes, respiratory system and skin. R42 / 43 May cause an allergic reaction to the respiratory tract, also in contact with skin. S23 Do not breathe gas. S36 / 37/39 Wear suitable clothing, gloves and eyewear. S46 If swallowed, seek medical advice immediately – show label or product package. S51 Use only in well-ventilated areas. S63 In case of poisoning of the respiratory tract, remove or transport the patient to fresh air and ensure rest.
Logistic information
packing | packaging | number on pallet | barcode | gross weight |
tin can | cardboard box | 65 boxes | pieces4820085760080 | pieces0,970 kg |
830 ml | 12 pcs. In the box | 780 pcs. | mailbox 4820085763883 | box 11,800 kg |
Notes.
Store upright. Storing the foam at temperatures above + 30 ° C reduces the shelf life to 9 months. Storage at -5 ° C for up to 5 days is allowed.
Foam transportation at negative temperatures is allowed: