CONTOUR 101 Universal Silicone

Properties:

excellent adhesion to non-porous surfaces: glass, ceramics, steel, aluminum and plastics. Elastic. Resistant to moisture, UV rays, detergents. Antifungal. Not painted. Not applicable to marble, concrete, plaster, decorative stone (granite, sandstone, etc.), copper and its alloys, polyethylene, bitumen, rubber; materials, emitting oils and solvents. Not recommended for gluing mirrors, gluing and sealing aquariums. Not intended for products in contact with food and for medical purposes.

Technical data:

Consistency	sticky paste
Curing system	acidic
Density	1000 ± 10 kg / m 3
Working temperature	+ 5 ° С / + 40 ° С
Film formation time	10-30 minutes (23 ° C / RH 50%)
Cure time	2 mm per day (23 ° C / RH 50%)
Resistance to runoff	0 mm (SIST EN 27390)
Storage temperature	-5 ° С / + 25 ° С
Shelf life	24 months
After curing
Modulus of elasticity at 100% elongation	> 0.30 MPa (SIST EN 28339)
Tensile elongation	300 – 400% (SIST EN 28339)
Stretching to break	0.5 – 0.6 MPa (SIST EN 28339)
Allowable deformation	± 20%
Change in volume	<10% (ISO 10563)
Recovery of elasticity	> 95% (SIST EN 27389)
Shore A hardness	15-25 (ISO 868)
Heat resistance	-40 ° С / + 180 ° С

* the rate of solidification slows down significantly at low temperatures.

Application:

clean, degrease and dry the surface. Trim the cartridge above the thread. Cut off the tip to the width of the seam and screw it onto the cartridge. Extrude with a pistol. ** Smoothing of the seam is allowed with soap and water.

Attention!

S2 Keep out of the reach of children. S24 / 25 Avoid contact with skin and eyes. S26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. S51 Use only in well-ventilated areas.

** when using a 280 ml cartridge, the packaging of a 70 ml gun does not require.

Logistics information:

packing	packaging	number on pallet	Colour	barcode	gross weight
plastic cartridge with tip and cap	cardboard box	120 boxes	white	pieces 4820085764620	pieces 0.330 kg
			transparent	4820085764613	0.330 kg
			the black	4820085764668	0.330 kg
			Gray	4820085764637	0.330 kg
			brown	4820085764651	0.330 kg
			beige	4820085764644	0.330 kg
280 ml	12 pcs. In the box	1440 pcs.	–	mailbox 48.8 billion	box 4,16 kg
plastic cartridge with a tip and extrusion rod	paper box, cardboard box	180 boxes	white	pieces 4820085764606	pieces 0.110 kg
			transparent	4820085764590	0.110 kg
70 ml	20 pcs. In the box	3600 pcs.	–	mailbox 48.8 billion	box 2.40 kg

Notes:

The recommended minimum joint width should be 6 mm. For joints between 6 and 12 mm wide, the recommended depth is 6 mm. In the case of a seam width of more than 12 mm, the ratio of width to depth A: B should be 2: 1, to max. depth 12 mm. In the case of deeper seams, as well as where it is necessary, a polyethylene cord should be used, with a minimum layer thickness of 6 mm. The polyethylene cord should be used wherever the return voltage can protrude or to avoid running through to three surfaces, which limits the sealant’s adaptation to movement.