High quality single component acetate silicone sealant. Appointment: isolation, sealing of joints, filling of cracks and seams in and outside of rooms.
excellent adhesion to non-porous surfaces: glass, ceramics, steel, aluminum and plastics. Elastic. Resistant to moisture, UV rays, detergents. Antifungal. Not painted. Not applicable to marble, concrete, plaster, decorative stone (granite, sandstone, etc.), copper and its alloys, polyethylene, bitumen, rubber; materials, emitting oils and solvents. Not recommended for gluing mirrors, gluing and sealing aquariums. Not intended for products in contact with food and for medical purposes.
Consistency | sticky paste |
Curing system | acidic |
Density | 1000 ± 10 kg / m 3 |
Working temperature | + 5 ° С / + 40 ° С |
Film formation time | 10-30 minutes (23 ° C / RH 50%) |
Cure time | 2 mm per day (23 ° C / RH 50%) |
Resistance to runoff | 0 mm (SIST EN 27390) |
Storage temperature | -5 ° С / + 25 ° С |
Shelf life | 24 months |
After curing | |
Modulus of elasticity at 100% elongation |
> 0.30 MPa (SIST EN 28339) |
Tensile elongation | 300 – 400% (SIST EN 28339) |
Stretching to break | 0.5 – 0.6 MPa (SIST EN 28339) |
Allowable deformation | ± 20% |
Change in volume | <10% (ISO 10563) |
Recovery of elasticity | > 95% (SIST EN 27389) |
Shore A hardness | 15-25 (ISO 868) |
Heat resistance | -40 ° С / + 180 ° С |
* the rate of solidification slows down significantly at low temperatures.
clean, degrease and dry the surface. Trim the cartridge above the thread. Cut off the tip to the width of the seam and screw it onto the cartridge. Extrude with a pistol. ** Smoothing of the seam is allowed with soap and water.
S2 Keep out of the reach of children. S24 / 25 Avoid contact with skin and eyes. S26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. S51 Use only in well-ventilated areas.
** when using a 280 ml cartridge, the packaging of a 70 ml gun does not require.
packing | packaging | number on pallet | Colour | barcode | gross weight |
plastic cartridge with tip and cap | cardboard box | 120 boxes | white | pieces 4820085764620 |
pieces 0.330 kg |
transparent | 4820085764613 | 0.330 kg | |||
the black | 4820085764668 | 0.330 kg | |||
Gray | 4820085764637 | 0.330 kg | |||
brown | 4820085764651 | 0.330 kg | |||
beige | 4820085764644 | 0.330 kg | |||
280 ml | 12 pcs. In the box | 1440 pcs. | – | mailbox 48.8 billion |
box 4,16 kg |
plastic cartridge with a tip and extrusion rod | paper box, cardboard box | 180 boxes | white | pieces 4820085764606 |
pieces 0.110 kg |
transparent | 4820085764590 | 0.110 kg | |||
70 ml | 20 pcs. In the box | 3600 pcs. | – | mailbox 48.8 billion |
box 2.40 kg |
The recommended minimum joint width should be 6 mm. For joints between 6 and 12 mm wide, the recommended depth is 6 mm. In the case of a seam width of more than 12 mm, the ratio of width to depth A: B should be 2: 1, to max. depth 12 mm. In the case of deeper seams, as well as where it is necessary, a polyethylene cord should be used, with a minimum layer thickness of 6 mm. The polyethylene cord should be used wherever the return voltage can protrude or to avoid running through to three surfaces, which limits the sealant’s adaptation to movement.