Products

PF-218 enamel
October 2, 2018
Enamel PF-5135
October 2, 2018

Enamel PF-1145

Enamels PF-1145, PF-5135 PUMP  TOU 24.3-02972374.009-2001. Scope:  For painting of external metal surfaces of decks of vessels of the unlimited area of ​​navigation, which are subject to requirements for atmospheric resistance, wear resistance and anti-slip properties (PF-1145, PF-5135). 

Categories: ,

Tanks and containers containing petroleum products and lightweight volatile liquids, and other metal surfaces to which the requirements for atmospheric resistance are provided, and heat-reflective properties (PF-5135).

It provides protection against corrosion in systems with suitable primers for 3 years in temperate and cold climates and 2-2.5 years in tropical climates.

Properties

  • High atmospheric resistance, moisture resistance and resistance to mineral oils;
  • Possibility of obtaining anti-slip coating (with the introduction of sand or electrocorundum);
  • Enamel PF-5135 has thermal reflection properties (when you add 10% heat-reflective additive).
Technical data
Stock Pentafalt lacquer, pigments, fillers, solvents, siccatives and special additives
Dry residue 63-69% (PF-1145)
56-66% (PF-5135)
Conditional viscosity (70-120) s (PF-1145)
(60-110) s (PF-5135)
Solvent White spirit, Solvent
Packaging 50 kg
Guaranteed shelf life 12 months from the date of manufacture
Instructions on applying enamel
Methods of drawing Working viscosity (VZ-4)
portage, penzel (50-60) with
spray pneumatic (20-30) with
spray airless (40-50) with
Special instructions Розведення емалі допускається в кількості не більше 12 % розчинника від маси емалі.
Після розведення в емаль ПФ-5135 вводять тепловідображаючу добавку. Строк придатності емалі після введення добавки – 72 години.
Для надання протиковзких властивостей при фарбуванні емаллю ПФ-1145 на свіжопофарбовану поверхню першого шару емалі насипають протиковзку добавку (пісок марок 1К1О1016, 1К1О2016 або електрокорунд нормальною зернистістю 400 мкм марок 13А, 14А або 15А). Після висихання емалі залишки добавки змітають і наносять другий шар емалі.
Умови роботи Температура повітря при фарбуванні від +5 до +35 °С та відносній вологості повітря не більше 80 %.
Тривалість висихання At a temperature (18-22) ° C and a relative humidity of no more than 65% – up to 24 hours.
The lower temperature and higher humidity of the air prolong the drying drying time
Consumption of enamel On a single-layer coating for enamel PF-1145- (60-75) g / m? .
On a single-layer coating for enamel PF-5135- (100-120) g / m? .
Thickness of single-layer coating (18 – 23) μm – when applied by spraying methods
(20 – 50) μm – when applied with a roll or brush.
For high-quality coating it is recommended to apply two layers of enamel.
Cleaning tools White spirit

Preparation of the surface
Remove dust, dirt, particles of old paint, exfoliate, grease and other contaminants. The surface should be dry and clean.

Metal surfaces: ground with primers VL-02, EF-065, EF-1219 if necessary, to work with a grinding sheet.

Preparing the enamel
Thoroughly mix and dilute to the working viscosity. 

up