Enamel ML-1214 ME

Specifications

No	The name of indicators	Requirements TNPA
one	Enamel coating color:	Must-have-been-set-up of a liquid-shining pattern; shade is not standardized.
2	The appearance of the coating	It should be a glossy skin effect, it should be shakreen is allowed.
3	Of viscosity of type VZ-246 (nozzle 4 mm), at a temperature of (20.0 ± 0.5) ° C, s	50 – 90
four	Mass fraction of nonvolatile substances of enamel,%	45 ± 3
five	Enamel drying time to degree 3 at (130 – 135) ° С, min, not more than	thirty
6	Bending elasticity of the coating, mm, not more	one
7	Coating strength at impact on U-1 device, cm, not less	50
eight	Coating hardness by pendulum device type TML (pendulum A), relative units, not less	0.25
9	Gloss coating onelectric gloss meter FB-2,%, not less	53
ten	Adhesion of coating points	2 1
eleven	Resistance to a temperature of (20 ± 2) ° С, h, not menevody gasolineindustrial oil	2424 24
12	Conventional light resistance of the coating, h, not less	6
13	H / m 2 , no more: dark yellow other colors	80 60
14	Covering service life under operating conditions: UHL1, years, not less T1, years, not less	2 one

 

 

 

Benefits:  Enamel provides a highly glossy finish with a metallic effect. Enamel coatings have high decorative properties when used in atmospheric conditions and indoors. The enamel coating is minus 60 ° C to plus 60 ° C.

 

 

 

         Surface preparation:  Before applying the enamel, the primed surface is sanded, dedusted, degreased and dried thoroughly if necessary. The surface is mechanically cleaned, dehydrated, degreased and dried. The temperature should not be below 3 ° C. Recommended primers: EP-045,

EP-045K (TU BY 5000021625.106), GF-0119 (GOST 23343) produced by Lakokraska.

 

 

 

Recommendations for application:  Enamel is applied to the primed surface using pneumatic and electrostatic spraying. When tinting small areas of enamel can be applied with a brush.

 

Before use, the enamel is thoroughly mixed and, if necessary, filtered. When applied by pneumatic spraying, the enamel is diluted with xylene (GOST 9949 or GOST 9410), orthoxylene

(TU BY 300042199.015) or thinner P-197 (TU 6-10-1100) in an amount of 18 – 25% by weight of undiluted enamel, when applied by electrostatic method sputtering – RE-2B diluent (GOST 18187) in the quantity necessary to achieve specific volume electrical resistance in the range from 5 · 104 to 5 · 105 Ohm · m. When applied with a brush, the enamel, if necessary, is diluted with xylene

(GOST 9949 or GOST 9410), orthoxylene (TU BY 300042199.015) or thinner P-197 (TU 6-10-1100) in an amount of not more than 5% by weight of the undiluted enamel.

 

The temperature is between 15–25 ° C and the temperature of (20 ± 2) ° C and final drying a temperature of 130 to 135 ° C within 30 min. After drying, should not be at least 40 microns.

 

 

 

Of The  ENAMEL consumption for a to two two-dried coating of layer with a thickness of

30–40 µm is 70–100 g / m² without reference to the preparation of the personnel and other factors.

 

 

 

Enamel Coating Service life:  A coating system applied on a primed surface (primer EP-045

(TU BY 5000021625.106) 10-15 microns thick for 1 year.